Permanent Threadlocker - Technical Data

Technical Data

PRODUCT: Permanent Threadlocker/Sealant

PART NOS: 49451, 49452, 49454

DESCRIPTION

DynaGrip Permanent Threadlocker/Sealant is a specially developed Medium to High Strength Threadlocker, where controlled torque/tension is required. Lubricates during assembly, securing parts with High Strength retention, allowing disassembly when required.

APPLICATIONS

Where parts require locking but need to be disassembled. DynaGrip Permanent Threadlocker/Sealant resists vibration loosening and offers augmentation of on torque. On large diameter bolts or where there is a long engagement of the stud, the application of heat may be required for removal.

USEFUL HINTS/NOTES

DynaGrip Permanent Threadlocker/Sealant offers an advantage of Torque augmentation. Treated fasteners exhibit 20% + Breakloose to on Torque applied during assembly. Lubricating ability during assembly, medium to high strength locking action.

PROPERTIES

While DynaGrip Permanent Threadlocker/Sealant will perform on light oily surfaces, a reduction in strength of up to 10% may be expected.

INSTRUCTIONS FOR USE

Ensure parts are clean, dry and free from oil and grease.

PROCEDURE FOR APPLICATION

Product is normally hand applied from the bottle.

COMPATIBLE ACCELERATORS/PRIMER

Primers such as Primer N or the faster primer, primer T can be used. However, up to 30% strength loss can occur when using primer.

TECHNICAL FEATURES

Resin: . . . . . . . . . . . . . . . . . . . . . . Dimethacrylate

Color: . . . . . . . . . . . . . . . . . . . . . . Red

Cure Speed with Activator: . . . . . . <5 minutes

Cure Speed without Activator: . . . 5 min @ 25ºC (77ºF)

Viscosity (Thixotropic): . . . . . . . . . 1900-6800cps

Gap Fill: . . . . . . . . . . . . . . . . . . . . . .0.127mm (005")

Flash Point: . . . . . . . . . . . . . . . . . . >212ºF

Shelf Life: . . . . . . . . . . . . . . . . . 12 months @ 20ºC (68ºF)

Specific Gravity: . . . . . . . . . . . . . . 1.1-1.15

Max. Operating Temperature: . . . . –18ºC to 148ºC (-65ºF to + 300ºF)

CURED PERFORMANCE

Full Cure Time: . . . . . . . . . . . . . . 12 hours @ 20ºC (68ºF)

Typical Breakaway Strength: . . . . 1.73-2.88 Kg/M (150-250 lbs")

Typical Prevailing Strength: . . . . . 1.15-2.30Kg/M (100-200 lbs")

STORAGE

Store in a cool area out of direct sunlight. Shelf Life: 12 months @ 20ºC (68ºF).

PRESENTATION

Bottles: . . . .. . . . . . . . 6ml

HEALTH & SAFETY IN USE

IRRITANT: Contains Methacrylate Esters and some products contain small amounts of Acrylic Acid. Irritates the eyes, the respiratory organs and the skin. In case of contact with the skin, wash immediately with plenty of water.

REVISED 03/31/99
TDSTL62

The information contained herein is produced in good faith and is believed to be reliable but is for guidance only

AFC International Pty. Limited and its agents cannot assume liability or responsibility for results obtained in the use of its product by persons whose methods are outside or beyond our control. It is the users responsibility to determine the suitability of any of the products and methods of use or preparation prior to use mentioned in our literature and furthermore the users responsibility to observe and adapt such precautions may be advisable for the protection of personnel property in the handling and use of any of our products.