PLASTIC WELD
Material Safety Data Sheet I. PRODUCT IDENTIFICATION: DD6580s Plastic Welding System – Part A Resin II. COMPOSITION INGREDIENTS CONCENTRATION% C.A.S.# ACGIH TLVMethyl methacrylate (MMA)* 60-85 80-62-6 100ppm Acrylated copolymers 12-30 trade secret --- Methacrylic Acid* 6-12 79-41-4 20ppm Cumene Hydroperoxide* 1-4 80-15-9 --- *SARA Section 313 Toxic Chemicals III. CHEMICAL AND PHYSICAL PROPERTIES
Vapor Pressure: 29mmHg @ 20C IV. FLAMMABILITY AND EXPLOSIVE PROPERTIES
Flashpoint (T.C.C.):
51F V. REACTIVITY DATA
Stability:
Stable VI. SPILL OR LEAK PROCEDURESRemove sources of ignition. Use with ventilation. Dike area to prevent spreading. Absorb on vermiculite, sand or other inert absorbing material. Dispose of as a chemical waste in accordance with current local, state, and federal regulations. Do not discharge into water. Wash spill area with strong detergent. After proper mixing of resin and activator sides, the material will polymerize into a cured solid state which can be treated as a nonhazardous solid. Applicable CERCLA/RCRA waste code: 0001 (ignitability) U162 (MMA). VII. STORAGE AND HANDLING PROCEDURESStorage: Avoid storage over 100F, contamination with incompatible materials. Store in cool place away from direct sunlight. Handling: Avoid prolonged or repeated breathing of vapor. Avoid contact with skin and eyes. Wash hands before smoking or eating. VIII. SHIPPING REGULATIONSDOT and IATA Hazard Classification:ORM-D in plastic containers or small volume cans, 1 gallon or less. Proper DOT Shipping Name – bulk for containers over 1 gallon in volume: Adhesive containing flammable liquid, class 3, UN1133, PGIII, flammable liquid label required. IX. EMERGENCY TREATMENTEye Irritation: Immediately flush eyes with water for at least 15 minutes. Get medical attention. Skin Contact: Wash thoroughly with soap and water. Discard contaminated clothing. Do not use organic solvents on skin. For long term exposure or in case of irritation, get medical attention. Inhalation: Remove person to fresh air. Get medical attention if short of breathe or if respiratory symptoms develop. Ingestion: Give 1-2 glasses of milk or water to conscious person. Do not induce vomiting. Get medical attention. X. PERSONAL PROTECTIONRespiratory: Use proper positive airflow ventilation in work areas/explosion proof equipment in confined areas where vapors may exceed TLV limits. Skin: Avoid skin contact, wear impervious gloves and protective clothing if in direct contact with material. Disposable polyethylene gloves with vinyl latex overgloves will give protection. Eyes: Wear safety goggles or side shield safety glasses. Do not wear contact lenses. XI. HEALTH HAZARD DATAHazard Categories: immediate X delayed X fire X pressure reactivity Potential Routes of Entry: skin X inhalation X ingestion X Symptoms of Overexposure: Possible skin and eye irritation on contact is likely. Vapor may irritate throat. Exposure limits: ACGIH OSHA OTHER Ingredients Methyl Methacrylate 100ppm 100ppm 100ppm Canada Methacrylic acid 20ppm 20ppm Target organs Carcinogen NTP IARC OSHA None None None Sara Listed Ingredients: Methyl methacrylate, methacrylic acid, cumene hydroperoxide I. PRODUCT IDENTIFICATION: Plastic Fusion - Part B: Activator II. COMPOSITION INGREDIENTS CONCENTRATION% C.A.S.# ACGIH TLVMethyl methacrylate (MMA)* 60-85 80-62-6 100ppm Acrylated copolymers 12-30 trade secret --- Amine condensate 0.5-5 trade secret --- Metal salt, acid complex solution 0.1-1 trade secret --- *SARA Section 313 Toxic Chemicals III. CHEMICAL AND PHYSICAL PROPERTIES
Vapour Pressure: 29mmHg @ 20°C IV. FLAMMABILITY AND EXPLOSIVE PROPERTIES
Flashpoint (T.C.C.):
10°C(51°F) Hazardous Products Formed by Fire or Thermal Decomposition: Toxic fumes of carbon oxides may evolve upon exposure to heat or open flame. Use self-contained breathing apparatus if burning. Unusual Fire or Explosive Hazards: none Closed containers may burst when heated. Cool containers with water spray.
Compressed
gases: none V. REACTIVITY DATA
Stability: Stable VI. SPILL OR LEAK PROCEDURESRemove sources of ignition. Use with ventilation. Dike area to prevent spreading. Absorb on vermiculite, sand or other inert absorbing material. Dispose of as a chemical waste in accordance with current local, state, and federal regulations. Do not discharge into water. Wash spill area with strong detergent. After proper mixing of resin and activator sides, the material will polymerize into a cured solid state which can be treated as a nonhazardous solid. Applicable CERCLA/RCRA waste code: 0001 (ignitability) U162 (MMA). VII. STORAGE AND HANDLING PROCEDURESStorage: Avoid storage over 37°C (100°F), contamination with incompatible materials. Store in cool place away from direct sunlight. Handling: Avoid prolonged or repeated breathing of vapour. Avoid contact with skin and eyes. Wash hands before smoking or eating. VIII. SHIPPING REGULATIONSDOT and IATA Hazard Classification:ORM-D in plastic containers or small volume cans, 3.7 Litres (1 gallon) or less. Proper DOT Shipping Name – bulk for containers over 1 gallon in volume: Adhesive containing flammable liquid, class 3, UN1133, PGIII, flammable liquid label required. IX. EMERGENCY TREATMENTEye Irritation: Immediately flush eyes with water for at least 15 minutes. Get medical attention. Skin Contact: Wash thoroughly with soap and water. Discard contaminated clothing. Do not use organic solvents on skin. For long term exposure or in case of irritation, get medical attention. Inhalation: Remove person to fresh air. Get medical attention if short of breathe or if respiratory symptoms develop. Ingestion: Give 1-2 glasses of milk or water to conscious person. Do not induce vomiting. Get medical attention. X. PERSONAL PROTECTIONRespiratory: Use proper positive airflow ventilation in work areas/explosion proof equipment in confined areas where vapours may exceed TLV limits. Skin: Avoid skin contact, wear impervious gloves and protective clothing if in direct contact with material. Disposable polyethylene gloves with vinyl latex overgloves will give protection. Eyes: Wear safety goggles or side shield safety glasses. Do not wear contact lenses. XI. HEALTH HAZARD DATAHazard Categories: immediate X delayed X fire X pressure reactivity Potential Routes of Entry: skin X inhalation X ingestion X Symptoms of Overexposure: Possible skin and eye irritation on contact is likely. Vapour may irritate throat. Exposure limits: ACGIH OSHA OTHER Ingredients Methyl Methacrylate 100ppm 100ppm 100ppm Canada Target organs Carcinogen NTP IARC OSHA None None None Sara Listed Ingredients: Methyl methacrylate XII. PREPARATION INFORMATIONPOISONS INFORMATION CENTRE
Adelaide: (08) 8204-6117 Brisbane: (07) 3253-8233
Canberra: (02) 6285-2852 Darwin: (08) 8922-8842
Hobart: (03) 6338-8485 Melbourne: (03) 9345-5678
Perth: (08) 9381-1177 Sydney: (02) 9692-6111
POLICE OR FIRE BRIGADE: 000 EXCHANGE: 1100
Information presented herein has been complied from sources considered to be dependable and is accurate and reliable to the best of our knowledge and belief but is not guaranteed to be so. Nothing herein is to be constructed as recommending any practice or any product in violation of any patent or in violation of any law or regulation. It is the user's responsibility to determine for himself the suitability if any material for a specific purpose and to adopt such safety precautions as may be necessary. We make no warranty as to the results to be obtained in using any material and, since conditions of use are not under our control, we must necessarily disclaim all liability with respect to the use of any material supplied by us. ISSUE DATE: 10/27/99 |
< close window >