|
Material Safety Data Sheet
This material is not
hazardous according to criteria of NOHSC
Not Classified as Dangerous Goods by the criteria of the Australian
Dangerous Goods Code (ADG Code) for transport by Road and Rail.
1. Identification of the substance/preparation and of the
company/undertaking
Product Name: DYNAGRIP BLUE SILICONE GASKET MAKER – 312grm cartridge
Supplier: AFC International Pty. Ltd..
ABN: 76 082 316 783
Street Address: 21-23 Hobart Street, Riverstone, New South Wales 2765
Australia
Telephone Number: +61 2 9627 7125 Facsimile: +61 2 9627 7126
Emergency Telephone: 0412 614 580 (24 HOURS)
Part Number: 49293 Issued: 12/04/2004 Version 2
2. Composition/Information on Ingredients
Product Description: Makes gaskets for high temperature applications up to
315 C.
COMPOSITION
%
CAS #
Risk Phrases
METHYLTRIACETOXYSILANE
1-10
253-34-3
R36/R37/R38
ETHYLTRIACETOXYSILANE
1-10
17689-77-9
R36/R37/R38
SILICA, AMORPHOUS
5-15
7631-86-9
3. Hazards identification Comment : Acetic acid is formed during curing on
exposure to water or humid air.
Provide adequate ventilation to control exposures to within the exposure
guideline of 10ppm (TWA).
Eye Contact: Direct contact irritates slightly with redness and swelling
Skin Contact: A single short exposure (<24 hours) may irritate. Repeated
prolonged contact (24 – 48 hours) may irritate moderately.
Inhalation: Vapour overexposure may irritate eyes, nose and throat.
Oral: Small amounts transferred to the mouth by fingers during use should
not injure. Swallowing large amounts may cause digestive discomfort.
Poisons Schedule: None Allocated
4. First-aid measures For advice, contact a Poisons Information Centre
(Phone eg. Australia 131 126; New Zealand 0 800 764766) or a doctor.
Skin: Remove from skin and immediately flush with water for 15 minutes. Seek
medical attention if irritation or ill effects develop or persist.
Inhalation: Remove victim to fresh air. Seek medical attention if ill
effects persists.
Eye Contact: Immediately flush eyes with water for 15 minutes. Seek medical
attention.
Ingestion: No first aid should be needed.
5. Fire-fighting measures
Specific Hazards: Combustible paste
.
Fire Fighting Advice: Combustible but under normal conditions of use is not
considered a risk.
Extinguishing Media: Water fog (or if unavailable fine water spray), Carbon
Dioxide, (CO2), Dry Chemical, Foam
Fire-fighting equipment: Fire fighters to wear self-contained breathing
apparatus and suitable protective clothing if risk of exposure to vapour or
products of combustion.
6. Accidental release measures
SMALL SPILLS: Slippery when spilt. Clean up immediately. Wipe up with rag or
absorbent paper. Any residual can be cleaned up with mineral turpentine or
similar hydrocarbon solvent, or acetone based nail polish remover. Cured
material can be removed by cutting or abrasion.
LARGE SPILLS: Slippery when spilt. Clean up immediately. Wear protective
equipment to prevent skin and eye contact. Avoid breathing in vapours. Work
up wind or increase ventilation. Scrape up excess material before cure.
Collect and seal in properly labelled containers or drums for disposal.
Cured material can only be removed by cutting or abrasion.
7. Handling and storage
Handling Advice: Avoid skin and eye contact and breathing in vapour.
Storage Requirements: Keep containers closed when not in use. Store in
clean, dry locations away from excessive heat
8. Exposure controls/personal protection Occupational Exposure Limits: No
value assigned for this specific material by the NOHSC Acetic evolved when
curing or exposed to water or humidity – OSHA Pel: TWA 10ppm, STEL 15ppm.
Engineering Control Measures: Ensure ventilation is adequate and that air
concentrations of components are controlled below any quoted Exposure
Levels. Use in well ventilated areas. Keep containers closed when not in
use.
Personal Protective Equipment:
Respiratory Protection: Wear organic vapour respirator meeting the
requirements of AS/NZS 1715 and AS/NZS 1716.
Ventilation: Use only with adequate ventilation. Local exhaust is
recommended. Mechanical exhaust can be used as a back up system.
Protective Gloves: Chemical resistant gloves such as PVC
Eye Protection: Approved safety glasses or goggles with side shields
Protective Clothing: Heavy cotton or polypropylene coats.
.
Comments: Wash hands before smoking, eating, drinking or using the toilet
9. Physical and chemical properties
Physical state: Blue paste with acetic acid like odour
Specific Gravity: 1.04
Vapour Density: N/A
Vapour Pressure: <5mm
Flash Point: N/A
Volatile Content: <5%
Solubility in water (g/L): < 0.1%
Boiling Point: N/A
Melting Point: N/A
10. Stability and reactivity
Stability: Stable
Polymerisation: Hazardous polymerisation cannot occur.
Chemical In compatibilities: Strong oxidising agents.
Conditions to avoid: None.
Hazardous Decomposition Products: Silicon dioxide, Carbon dioxide, traces of
incompletely Burned Carbon
Products. Traces of formaldehyde.
11. Toxicological information
No adverse health effects expected if product is handled in accordance with
this Safety Data Sheet. Symptoms or effects that may arise if the product is
mishandled and overexposure occurs are:
Ingestion: Swallowing may result in irritation to the mouth and throat. No
adverse effects expected after swallowing cured (solvent free ) sealant.
Skin contact: Repeated or prolonged contact may lead to irritation. Acetic
acid liberated is a skin irritant . Repeated or prolonged contact may lead
to allergic dermatitis in sensitive individuals. Cured sealant is not
expected to be a skin irritant.
Inhalation: Acetic acid liberated during cure may be irritating to the
mucous membranes of the respiratory tract.
12. Ecotoxicological information
Avoid contaminating waterways and sewers.
13. Disposal considerations
Refer to Waste Management Authority. Normally suitable for disposal at
approved land waste site.
14. Transport information
Road and Rail Transport
Not classified as Dangerous Goods by the criteria of the Australian
Dangerous Goods Code (ADG Code) for transport by Road and Rail.
Marine Transport
Not classified as Dangerous Goods by the criteria of the International
Maritime Dangerous Goods Code (IMDG Code) for transport by sea.
Air Transport
Not classified as Dangerous Goods by the criteria of the International Air
Transport Association (IATA) Dangerous Goods Regulations for transport by
air.
15. Regulatory information
Classification: Based on available information, not classified as hazardous
according to criteria of NOHSC.
Poisons Schedule: None allocated.
Risk Phrase(s): R36/37/38: Irritating to eyes, respiratory system and skin
Safety Phrase(s):
S26: In case of contact with eyes, rinse immediately with plenty of water
and seek medical advice.
S28: After contact with skin, wash immediately with plenty of soap and
water.
S36/S37/S39: Wear suitable protective clothing, gloves, eye and face
protection.
All the constituents of this material are listed on the Australian Inventory
of Chemical Substances (AICS).
16. Other information
Contact Point: AFC International P/L Technical Department
Phone: 61 2 9627 7125 (International) Local 02 9627 7125
Fax: 61 2 9627 7126 (International) Local 02 9627 7126
Mobile: 0412 614 580
Reason for Issue:
First Revision of Primary MSDS
This MSDS summarises to the best of the knowledge of AFC International Pty.
Ltd. at the date of issue, the chemical health and safety hazards of the
material and general guidance on how to safely handle the material in the
workplace. Since AFC International Pty. Ltd. cannot anticipate or control
the conditions under which the product may be used, each user must, prior to
usage, assess and control the risks arising from its use of the material.
If clarification or further information is needed, the user should contact
AFC International Pty. Ltd at the contact details above.
This MSDS summarises to the best of the knowledge of AFC International at
the date of issue, the chemical health and safety hazards of the material
and general guidance on how to safely handle the material in the workplace.
Since AFC International Pty. Ltd. cannot anticipate or control the
conditions under which the product may be used, each user must, prior to
usage, assess and control the risks arising from its use of the material.
|
